![]() Security – Controls and information about the intrusion detection system, which monitors things like doors, windows, and motion sensors.Provides quick viewing and control of your favorite zones, devices, cameras, and scenes. Dashboard/Home – Your landing page upon opening the app.Use the volume and music buttons on the side of the electronic chime to adjust the volume and ringtone. ![]() Note: One video doorbell can link up to 4 electronic chimes. Install the doorbell power pin to the doorbell chime and then pair it to your video doorbell. Then follow the on-screen instructions in EufySecurity App to connect the video doorbell to your home Wi-Fi.įollow the on-screen instructions in EufySecurity App. Wait until the doorbell ring flashes yellow. Switch the master circuit breaker in your house back to ON. What are required: Mounting Bracket / Screw Packs / 15° Mounting Wedge(Optional) / PhillipsHead Screwdriver Insert the two screws provided through the screw holes or through the 15° mounting wedge(Install the mounting bracket to the 15° mounting wedge in prior), and fasten the screws tightly. Lead the two doorbell wires through the central square hole on the bracket before start mounting. There is no need to use anchor If you were installing on wooden doorframe. Use the anchors provided when installing in materials such as stucco, brick, or concrete. Optional: Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side. What are required: Power Drill with 1/4" (6.35mm) Drill Bit / Screw Hole Positioning-Card Use the Screw Hole Positioning-Card to mark the screw holes in the place of the existing doorbell button, place it at least 1.2m(48") high from the ground for optimal viewing result, then drill holes (Use 1/4" (6.35mm) drill bit). Check if you can reuse the existing holes on the wall. What's required: Phillips-Head Screwdriverĭetermine the mounting position of the doorbell. Pull the two wires out carefully when removing the old doorbell. Remove the existing doorbell button at the front door. What are required: Jumper for existing chime / Phillips-Head Screwdriver When the jumper is in place, the existing chime will not sound anymore.If your doorbell chime has different markings or you have multiple chimes, refer to the help session in the App for the custom wiring instructions or consult a qualified electrician. Do not remove the original wire connecting to the chime. Use the provided jumper to connect FRONT and TRANS terminals to bypass the chime on the circuit.Find the existing doorbell chime in your house, remove the cover and take a photo of the wire connection in case you need to reconnect it. In most cases, the existing doorbell circuit looks like below chart.Without this step, the video doorbell will still be able to power on but will operate unstably. The video doorbell requires user to bypass the existing chime first to get sufficient power.If you're not comfortable to do it yourself, do consult a qualified electrician. Note: Always be careful when handling electricity wiring. Turn the lights in your home on / off to make sure the electricity in your house is properly shut off. Shut off the master circuit breaker in your house. Ring the existing doorbell, make sure it's working and locate the place of your existing chimes in the house. Note: Make sure you have installed the EufySecurity App and scan the QR code before start handling the doorbell installation. QR code can be found on the back of the video doorbell and the on the back of the documentation box.ĭeal with the physical installation first then come back to the App for in-App setup. Add video doorbell (Wired) and scan the QR code for later installation process. Search keyword " EufySecurity" on App Store or Google Play and install the App on your phone. In order to get sufficient power from the doorbell circuit, user needs to bypass the existing doorbell chime on the circuit. The video doorbell is powered by existing doorbell wires. The other is the electronic chime plugged on indoor power socket. The Video Doorbell system includes 2 parts. Power Drill with 1/4" (6.35mm) Drill Bit How the System Works
0 Comments
Leave a Reply. |